Rose-electronic Crystal View Bedienungsanleitung

INSTALLATION AND OPERATION MANUAL FOR SERIAL/AUDIO MODEL

QUICK START CrystalView Installation and Operations Manual 4 Step 4– Connect CAT-5 Cable (See Page 19 for details) 1. Connect Local U

QUICK START CrystalView Installation and Operations Manual 5 Remote Unit Step 5 – Adjust the Video Compensation (See Page 20 for details)

INTRODUCTION CrystalView Installation and Operations Manual 6 Introduction Thank you for choosing the Rose Electronics CrystalView KVM stati

INTRODUCTION CrystalView Installation and Operations Manual 7 With the CrystalView, you can reduce noise and heat, increase desk and floor spa

INTRODUCTION CrystalView Installation and Operations Manual 8 Compatibility Computers PCs with standard PC Keyboards and PS/2 mice, 286, 38

INTRODUCTION CrystalView Installation and Operations Manual 9 Package Contents The package contents consists of the following: • The Crysta

SYSTEM OVERVIEW CrystalView Installation and Operations Manual 10 System Overview The CrystalViews two Units, (Local and Remote) work together

SYSTEM OVERVIEW CrystalView Installation and Operations Manual 11 Changing SW1 position 2 can change the default “Hot Key” from t

SYSTEM OVERVIEW CrystalView Installation and Operations Manual 12 In this configuration, the local unit can be either a Dual or Single model.

MODELS/CABLES CrystalView Installation and Operations Manual 13 CrystalView Models (Top) Remote Unit – (Middle) Single Local Unit – (Bottom) D

LIMITED WARRANTY Rose Electronics warrants CrystalView to be free from defects in materials and workmanship and in good working order for a period o

MODELS/CABLES CrystalView Installation and Operations Manual 14 CrystalView to Rose switch Cable To connect a CrystalView Unit to a Rose swit

INPUTS/OUTPUTS CrystalView Installation and Operations Manual 15 Figure 3 shows the rear connectors for a Single, Dual and Remote model with t

INSTALLATION CrystalView Installation and Operations Manual 16 Installation Installation of the CrystalView consists of four easy steps. 1.

INSTALLATION CrystalView Installation and Operations Manual 17 TIP: If you are using a cable that is close to the top end of the cable length

INSTALLATION CrystalView Installation and Operations Manual 18 Figure 4. CrystalView Remote PCB (w/Daughter board)

INSTALLATION CrystalView Installation and Operations Manual 19 Step 2: Connecting the Cables Power down your PC and connect the appropriate

INSTALLATION CrystalView Installation and Operations Manual 20 Step 3: Applying Power Before applying power, set the Bright and Sharp contro

INSTALLATION CrystalView Installation and Operations Manual 21 Note: The CrystalView Video compensation system is designed to produce very go

INSTALLATION CrystalView Installation and Operations Manual 22 Installing Serial Devices (See Appendix A1. Serial Option Specifications) C

INSTALLATION CrystalView Installation and Operations Manual 23 Installing Audio Devices (See Appendix A2. Audio Option Specifications). Crys

LIMITED WARRANTY Copyright  Rose Electronics 1990-2001. All rights reserved. No part of this manual may be reproduced, stored in a retrieval system,

INSTALLATION CrystalView Installation and Operations Manual 24 User Selectable Settings Table 2 summarizes SW1 switch settings for the Remot

INSTALLATION CrystalView Installation and Operations Manual 25 Dual, serial/audio model specific notes • Default “Hot Key” is Right Control

OPERATING INSTRUCTIONS CrystalView Installation and Operations Manual 26 Operating Instructions- All Units Once the Remote and Local Units ar

OPERATING INSTRUCTIONS CrystalView Installation and Operations Manual 27 Private Mode (Dual model only) The private mode feature disables eith

OPERATING INSTRUCTIONS CrystalView Installation and Operations Manual 28 Hot Key Summary (First press and release the “Hot Key” (default is

TROUBLESHOOTING CrystalView Installation and Operations Manual 29 Troubleshooting The troubleshooting section is used as a guide to understandi

TROUBLESHOTING CrystalView Installation and Operations Manual 30 PS/2 Mouse cursor appears on the screen, but Mouse does not work. • Press

TROUBLESHOOTING CrystalView Installation and Operations Manual 31 Video Picture is not sharp or is smeared. • Video compensation incorrectly

TROUBLESHOTING CrystalView Installation and Operations Manual 32 A constant vertical wobble appears down the screen. • The CAT-5 cable con

SERVICE INFORMATION CrystalView Installation and Operations Manual 33 Service Information Maintenance and Repair This Unit does not contain an

FCC/IC STATEMENTS, EU DECLARATION OF CONFORMITY FEDERAL COMMUNICATIONS COMMISSION AND INDUSTRY CANADA RADIO-FREQUENCY INTERFERENCE STATEMENTS This

SAFETY CrystalView Installation and Operations Manual 34 Safety This CrystalView KVM extender has been tested for conformance to safety regula

SAFETY CrystalView Installation and Operations Manual 35 Safety and EMC Regulatory Statements Safety Information Documentation reference symb

SAFETY CrystalView Installation and Operations Manual 36 Safety and EMC Regulatory Statements Informations concernant la sécurité Symbole de

APPENDIXES CrystalView Installation and Operations Manual 37 Appendix A. General Specifications Video bandwidth (-3db) Local Unit: 150 Mhz R

APPENDIXES CrystalView Installation and Operations Manual 38 Appendix A1. Serial Option Specifications Baud Rate Up to 19,200 Baud Data For

APPENDIXES CrystalView Installation and Operations Manual 39 Appendix B. UTP/STP Connection The Local and Remote connection cable is terminate

APPENDIXES CrystalView Installation and Operations Manual 40 Appendix C. Parts and Cables Part Number Description CRK-1P/SER Single KVM st

APPENDIXES CrystalView Installation and Operations Manual 41 Appendix D. Firmware Updates The CrystalView firmware may be updated by changing

APPENDIXES CrystalView Installation and Operations Manual 42 Appendix F. Rack Mount Instructions The optional rack mount kit includes the fo

APPENDIXES CrystalView Installation and Operations Manual 43 Appendix G. Rack Mount Illustration

TABLE of CONTENTS I Contents Quick Start Guide ... 1 In

GLOSSARY CrystalView Installation and Operations Manual 44 Glossary CAT 3 EIA/TIA 568 standard cable CAT 5 EIA/TIA 568 standard cable EIA E

INDEX CrystalView Installation and Operations Manual 45 Index cable, 5, 6, 7, 10, 14, 16, 17, 19, 20, 29, 30, 31, 32, 39, 40, 44 CAT-5, 6, 7,

TABLE of CONTENTS II Figures Figure 1. Typical Installation... 12 Figure

QUICK START CrystalView Installation and Operations Manual 1 Quick Start Guide Step 1- Set Jumpers (See Page 16 for details) 1. Remove cas

QUICK START CrystalView Installation and Operations Manual 2 Step 2 – Connect Local Units Cables (See Page 19 for details) 1. Connect CP

QUICK START CrystalView Installation and Operations Manual 3 Step 3 – Connect Remote Units Cables (See Page 19 for details) 1. Connect KV